In Tallahassee, metal roofing installation typically starts at $8 per square foot, while repairs begin at $450, but your actual price depends on roof size, material choice, and the complexity of your project. We believe in transparent pricing, so you will always know what to expect before any work begins.
Pricing guide
These rates are indicative. Every job is unique: size, access, complexity. Request a free estimate for exact pricing tailored to your situation.
| Service | Price | Details |
|---|---|---|
| Metal Roof Installation | From $8/sq ft | Complete metal roof installation for Tallahassee homes built for hurricane wind and tree fall. Complete metal roof installation for homes across Tallahassee and the Big Bend, Florida Building Code-approved panel systems with high wind-uplift ratings for hurricanes, tornadoes and falling oaks, installed over sealed underlayment for a 40-60 year service life. |
| Standing Seam Metal Roofing | From $10/sq ft | Concealed-fastener standing seam systems, the premium choice for Tallahassee homes. Panels roll-formed to length and mechanically seamed; with no exposed screws; top hurricane wind-uplift ratings and a reflective finish that cuts summer heat gain. |
| Metal Roof Replacement | From $9/sq ft | Full tear-off and replacement of storm-damaged, tree-hit or worn-out roofs. Full tear-off and replacement of storm-worn shingle or end-of-life metal roofs, old roofing hauled away, decking inspected and re-nailed to code, then a complete new metal system installed. Florida insurers must offer wind-mitigation credits, ask your carrier. |
| Metal Roof Over Shingles (Retrofit) | From $7/sq ft | Retrofit metal roofing laid over the shingles already on your Tallahassee home, no tear-off. A new metal roof installed directly over your existing asphalt shingles where the Florida Building Code allows it, no tear-off, less waste, lower cost. We check deck condition and code requirements first and tell you honestly when tear-off is the better call. |
| Metal Roof Repair | From $450 | Repair for loose, limb-hit or wind-lifted metal roofing across Tallahassee and Leon County. Repair of damaged, loose or storm-hit metal roofing, replacing panels dented by falling live oak limbs, resealing seams and penetrations, and fixing failed flashing before the next downpour finds its way inside. |
| Metal Roof Leak Repair | From $450 | Leak work for metal roofs that finds the real entry point before anything is patched. Priority leak response for metal roofs, leaks traced to their true source (failed fasteners, seam separation, flashing gaps, pipe boots and skylights) and fixed right, not just caulked over. Emergency tarping available after hurricanes and storms. |
| Screw Replacement & Re-Fastening | From $750 | Fastener replacement for metal roofs loosened by hurricane wind and summer heat. Heat, humidity and storm wind crack washers and loosen screws on older exposed-fastener roofs across the Big Bend, the top cause of slow leaks on farmhouses, barns and hunting lodges. Oversized screws and new washers fix it for a fraction of the cost. |
| Corrugated & Ribbed Panel Roofing | From $5.50/sq ft | Exposed-fastener panel roofs replaced or repaired for barns, shops and rural homes. Exposed-fastener metal roofing (corrugated, R-panel and 5V), the classic North Florida farmhouse roof and the workhorse for barns, shops, carports and lodges across the Red Hills. Quality panels installed with code-rated screw patterns and closures. |
| Metal Shingle Roofing | From $9/sq ft | Metal shingles that hold up to hurricane rain, hail and falling oak limbs. Metal shingles that deliver the look of architectural shingles, slate or shake with the lifespan of steel, a favorite for Tallahassee homeowners who want hurricane-rated metal with a traditional look. |
| Stone-Coated Steel Roofing | From $9/sq ft | Stone-coated steel in tile or shake profiles, rated for wind uplift and hail. Stone-coated steel systems combining steel strength with a textured traditional finish, strong hurricane wind performance, Class A fire rating and shake or tile profiles that suit Tallahassee's brick and traditional homes. |
| Copper & Specialty Metal Roofing | From $20/sq ft | Copper and specialty metal for porches, bays and dormers on the older homes here. Copper, zinc and terne-coated roofing for bay windows, porches, dormers and full architectural roofs, premium metals that suit the historic homes of Calhoun Street, Park Avenue and Los Robles. Custom fabrication for the fine details. |
| Metal Roof Coating & Painting | From $2.50/sq ft | Coatings that bring faded, streaked metal roofs back without replacing the panels. Restoration of faded, chalking or rusted metal roofs, surface prep, rust treatment and high-performance reflective coating systems that cut summer heat gain and extend roof life 10-15 years on homes, barns and lodges. |
| Flashing, Chimney & Skylight Repair | From $600 | Chimney and skylight flashing rebuilt so driving rain stays outside. Repair and custom fabrication of flashing around chimneys, skylights, valleys and wall transitions, the number one leak point on Tallahassee roofs in tropical downpours. In-house bent flashing for a precise watertight fit. |
| Snow Guards & Ice Protection | From $1,200 | Debris and ice guards fitted where they are needed, without putting new holes in panels. Snow guards are not needed in Tallahassee, but low-profile guards and rails can still keep Spanish moss, oak limbs and storm debris from sliding off steep metal roofs over entries. Honest guidance on whether yours needs them. |
| Storm & Wind Damage Repair | Free inspection | Storm damage repair for wind-lifted, limb-hit and hail-dented metal roofs. Repair of hurricane, tornado and fallen-oak damage to metal roofing, thorough documentation with photos, honest assessment of repair vs. replacement, and help documenting your insurance claim from inspection to completed work. |
| Metal Roof Inspection | Free estimate | A straight roof inspection for buyers, sellers and owners ahead of hurricane season. Complete metal roof inspections for homeowners, buyers and insurance requirements, fastener condition, seam integrity, flashing, roof-to-wall connections and wind-mitigation details, and a straight answer on remaining service life with a written report. |
| Gutters for Metal Roofs | From $9/linear ft | Seamless gutters sized for tropical downpours, hung together with the roof. Seamless gutter systems sized and mounted correctly for metal roofing, oversized downspouts for tropical cloudbursts and guards that keep oak leaves, pine needles and Spanish moss from clogging them. |
| Commercial & Agricultural Metal Roofing | Free estimate | Metal roofing for shops, barns and commercial buildings across the Red Hills. Metal roofing for barns, plantation lodges, equipment sheds, churches and light commercial buildings across Tallahassee and the Big Bend, from Red Hills plantations and Gadsden County farms to shops in town, with durable panel systems and repairs. |
What Affects the Price
- Roof size and material : Larger roofs require more materials and labor, and premium metals like copper or stone-coated steel cost more than standard panels.
- Roof accessibility and pitch : Steep roofs, multiple stories, or difficult access can increase labor time and safety requirements, raising the overall cost.
- Extent of damage or repairs needed : Minor leak repairs are less expensive, while extensive storm damage or full replacements involve more materials and labor.
- Additional features and cleanup : Items like skylight flashing, snow guards, or gutter installation add to the cost, and debris removal and cleanup are factored into the estimate.
What's included
- Travel included across the Tallahassee area
- Professional labor & equipment
- Old roofing tear-off & haul-away
- Job site cleanup
- Written estimate before work begins
To get an accurate estimate, have your roof dimensions, material preference, and any specific concerns ready before you call. A Tallahassee Metal Roofing estimate includes a detailed breakdown of materials, labor, and any additional services, with no hidden fees. Call (850) 404-0887 to schedule your free inspection and receive a written quote.
Pricing FAQ
Why do metal roofing prices vary so much?
Prices vary based on roof size, material type (e.g., corrugated panels vs. standing seam), roof complexity, and local labor rates. For example, copper roofing starts at $20 per square foot, while corrugated panels start at $5.50 per square foot.
Do you offer free estimates?
Yes, we provide free inspections and estimates for most services, including storm damage repair and commercial roofing. Call (850) 404-0887 to schedule your appointment.
What payment methods do you accept?
We accept cash, checks, and major credit cards. Financing options may be available for larger projects; please ask for details when you call.